< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=1724791474554128&ev=PageView&noscript=1" />

lm3875 PCB

  • Over 10 years’ experience of lm3875 PCB placas
  • Affordable lm3875 PCB
  • Excelente serviço ao cliente
  • A entrega rápida

O que é um medidor de energia trifásico PCB?

In electricity, phase means allocation of alternate current’s load.

In the single-phase, it has a phase wire, which is a power wire, and another side is neutral.

The three-phase power load is three alternate current supplies with a signal of 120 electrical degrees apart go through each phase wire.

The main advantage of a three-phase power load is that it could accommodate more power load than a single-phase power load.

A three-phase power load delivers a invariable power load.

Three-phase PCB is currently used in industrial and commercial environments.

Three-phase Energy Meter PCB
Layout analógico

Qual é o layout analógico do medidor de energia PCB?

The analog layout or circuit function by transfer go on voltage or current supply as a signaling way.

In general, analog layout or circuit are made of base on components of PCB like as transistors, capacitors, diodes, resistors, inductors, and other basic component.

The analog layout may be used a microcontroller, and the design is more difficult to be done compared to the digital layout.

Por que você usa microcontroladores em um PCB de medidor de energia?

The main reason is to use a microcontroller in an medidor de energia PCB to decrease the component size.

A microcontrolador PCB is a compact combine circuit that suffer a memory, a processor, input-output peripherals in a single chip.

So compact the space for several types of components which may be occued more spaces if they are used separately.

A microcontroller is good in space saver, time saver, and cost-effective.


Your Best LM3875 PCB Partner

Risco lm3875 PCB is a national company’s most popular amp. They are integrated into one of the webs a lot of applications.

Our lm3875 PCB has very good quality sound systems. So, they are widely used in LM3875 RMS 56W.

Venture lm3875 PCB gives music power 100w THD rate is very low clean sound.  Our lm3875 PCB is quite small in size.

Your Leading lm3875 PCB Supplier in China

Venture is a professional lm3875 PCB manufacturer and supplier in China for more than 10 years. We offer our clients the highest quality lm3875 PCB at the most affordable pricing.

Venture can also supply other design that is related to lm3875 PCB. And these are:

  • lm3915 vu medidor pcb
  • placa de alimentação lm723

Venture lm3875 PCB is less than 0.03% THD + N distortion in the audio frequency. It ranges 20 Hz-20KHz with DC voltage from +/- 20V to 40V.

The Venture lm3875 PCB includes circuitry to block a lot. The examples of this are:

  • block the signal or protect a spike of the power circuit
  • proteção contra curto-circuito
  • output over-voltage protection circuit
  • out of voltage or overload

You can rely on Venture lm3875 PCB as we fabricate hundreds of lm3875 PCB every day with our automated production line.

So, you don’t have to worry about big or small quantity orders.

Also, we have some sets of lm3875 PCB manufacturing lines and an lm3875 PCB fabrication facility.

Whether you are an lm3875 PCB distributor, retailer, or custom lm3875 PCB factory, Venture is always the right place for you.

At Venture, we provide the best preconditions to offer lm3875 PCB with price, speed, and possibilities.

We offer flexible payment terms, affordable rates, best delivery options, without MOQ to support your business and projects.

For more information about Venture lm3875 PCB, please don’t hesitate to contact our sales team today!

LM3875 PCB: The Ultimate FAQ Guide


I know choosing a suitable LM3875 PCB can be an overwhelming task.

A reason this guide will answer all questions you have been asking about LM3875 PCB.

So, if you want to be an expert in LM3875 PCB, read this guide.

What Are The Applications Of LM3875 PCB?

Some of the common uses of LM3875 PCBs are in making:

  • Component or compact stereos
  • Self-powered speakers
  • Surround-sound amplifiers
  • High-end stereo TVs

LM3875 PCB

LM3875 PCB

How Does LM3875 PCB Vs. LM3886 PCB Compare?

LM3875 PCBLM 3886 PCB
Outputs a continuous average power of 56W into 8 OhmOutputs a continuous average power of 68W into 4 Ohm
Has got an instantaneous peak output power capability of 100WHas got an instantaneous peak output power capability of 135W
Signal-to-noise ratio greater than 95dB (minimum)Signal to noise ratio greater than or equal to 92dB
Has got an output overvoltage protection against transients emanating from inductive loads.Has got an output overvoltage protection against transients emanating from inductive loads.
Has got supply under-voltage protectionAlso has got supply under-voltage protection
Has got an internal current limiting circuitry for output protection from a short to ground or to the supplies.Has got an internal current limiting circuitry for output protection from a short to ground or to the supplies.
Has got 11 lead TO-220 packageAlso has 11 lead TO-220 package
Has got wide supply voltage range of 20V to 84VHas got wide supply voltage range of 20V to 94V
LM3875 PCB will give out slightly more power at a load of 8 Ohms. However, it is not a good pick for speakers having impedances below 6 Ohms (4 Ohms included).LM3886 PCB will, in contrast, give better results with 4 Ohm speakers across the frequency range. It gives out around 10% higher sound pressure level across 20Hz-21.9KHz in 8 Ohm or 4 Ohm speaker with a sensitivity of 90dB.  That is why LM3886 is mostly recommended in general uses.
LM3875 PCB is a little flatterThe low end of LM3886 PCB is enhanced with a snubber inspired power supply making it less flat than LM3875 PCB.
LM3875 PCB is defined by some users to be warmer with better midrange and highs.LM3886 PCB has got bigger output transistor junctions. This leads to reduced total harmonic distortion, higher short-term power dissipation ability, and higher efficiency across a bigger range from 4 Ohms to 8 Ohms.

What Are The General Features Of LM3875 PCB?

The general features of an LM3875 PCB include:

  • Delivers an average power output of 56W to a load of 8 Ohm
  • Has got an instantaneous peak output power capability of 100W
  • Has got a signal to noise ratio greater than 95dB (minimum)
  • Has got an internal current limiting circuitry for output protection from a short to ground or to the supplies.
  • Has an in-built over-voltage protection circuitry against transients emanating from inductive loads.
  • Is designed to have supply under-voltage protection that does not allow internal biasing to happen thus getting rid of turn-on and turn-off transients.
  • Has got a supply voltage ranging widely from 20V to 84V

What Are The Components Of An LM3875 PCB?

O principal Componentes PCB of an LM3875 include:

  • Integrated Circuit LM3875T
  • Resistores
  • capacitores
  • Potenciômetro
  • Pinos
  • transformador
  • Retificador
  • Traços de cobre
  • Material de substrato

LM3875 PCB Assembly

LM3875 PCB Assembly

What Is The Continuous Average Output Power Of LM3875 PCB?

The continuous average output power of LM3875 PCB is 56W (that’s into a load of 8 Ohms).

Is There Standard Thickness Of LM3875 PCB?

There is no fixed standard thickness for LM3875 PCB. Various board thicknesses can be used depending on your assembly and fabrication needs.

One would easily say that 1.57mm, the historical standard PCB thickness, is the standard thickness for LM3875 PCB.

There are however other standard PCB thicknesses today such as 0.78mm and 2.36mm that can be adopted for LM3875 PCBs.

The factors that will determine the thickness of your LM3875 PCB board include:

  • Tipos de vias
  • Types of signal
  • Ambiente operacional
  • Número de camadas
  • Material de tabuleiro
  • Espessura de cobre
  • Equipamento de perfuração

What Is THD + N Of LM3875 PCB?

The total harmonic distortion plus noise (THD +N) for an LM3875 PCB is 0.06%. The 0.06% value is realised under the conditions: 40W, 20Hz≤f≤20kHz, Av=26dB.

How Do You Build LM3875 Gainclone PCB?

You can build your LM3875 PCB (DIY) using the following components among others:

  • 4 main capacitor filters
  • 2 LM3875 PCB chips
  • A printed board
  • 8 resistores
  • 16 diodes

After having everything you need under one roof, you can follow the following general steps to build your LM3875 PCB:

  1. Make a print-out for your LM3875 PCB ready
  2. Cut copper plate for the PCB
  • Transfer your print in (i) above to the copper plate in (ii). You can use iron box or other means
  1. Etch the plate
  2. Clean the plate and dispose the etching solution and other materials you don’t need
  3. Drill holes on the plate and solder all your components.

What Is The Difference Between Music Power And Peak Power Of LM3875 PCB?

Music Power

This is a measurement of the peak output power capability of the LM3875 PCB. The measurement is taken using high quality external power supplies or in a short timespan so that the power supply does not sag.

Music power is measured under the assumption that the LM3875 PCB power supply sag will be insignificant with normal program music material.

Pico de energia

In contrast, peak power is the power output capability of the LM3875 PCB that can be delivered to the load. It is specified by the maximum voltage swing of the LM 3875 PCB.

Why Is Heat Sinking Necessary In An LM3875 PCB Design?

Heat sinking in the LM3875 PCB helps in keeping the die temperature at a level by dissipating IC power.

That helps in preventing the thermal protection circuitry from turning on when conditions are normal and no protection is needed.

How Do You Measure The Power Bandwidth Of LM3875 PCB Assembly?

The power bandwidth of an LM3875 PCB is measured using frequencies at which a specified level of distortion is experienced.

At that frequency, the LM3875 PCB power output is 3dB below the rated power output.

Consider an example of an LM3875 PCB rated at 60W, with ≤0.25% THD +N.

The power bandwidth is obtained from the difference between the upper and lower frequencies at the 0.25% distortion as LM3875 PCB delivers 30W.

What Is The Importance Of Determining Maximum Power Dissipation During LM3875 PCB Heatsinking?

Selecting a heat sink for an LM3875 PCB that can achieve maximum power dissipation helps in realising adequate heatsinking.

That has the benefit of stopping the thermal shutdown circuity from operating under normal circumstances which would limit output power.

How Do You Avoid All Possible Oscillations In LM3875 PCB Assembly?

In order to get rid of oscillations, you need to bypass the supply leads of your LM3875 PCB using low inductance capacitors.

The capacitors should have short leads and should be fixed close to the terminals of the PCB.

The signs of inadequate power supply bypassing are low frequency oscillations or high frequency instabilities.

The instabilities can be avoided by using a large electrolyte or tantalum capacitor (10μF and above) and a small ceramic capacitor (0.1μF).

The purpose of the large capacitor is to absorb low frequency variations.

That of the small capacitor is to stop feedback of high frequencies through the power supply lines.

What Is The Ideal Signal-To-Noise Ratio (SNR) For LM 3875 PCB?

LM3975 PCB has got a a relação sinal-ruído (SNR) >95dB (minimum).

LM3875 Printed Circuit Board

LM3875 Printed Circuit Board

How Do You Protect LM3875 PCB From Low Impedance At High Frequencies?

LM3875 PCBs experience low impedance at high frequencies if the load being supplied is highly capacitive.

That can lead to oscillations or the square wave response will experience ringing.

High capacitance load could be as a result of long speaker cables. The LM3875 PCB can be protected in this scenario by coupling the load with a 10Ω resistor paralleled with a 0.7µH inductor.

Why Is Signal-To-Noise Ratio Vital In LM3875 PCB Assembly?

Signal to noise ratio (SNR) is the ratio between the power of a useful signal and the power of the unwanted signal.

The quality of signals in your LM3875 PCB would be retarded if its signal to noise raise is below the required parameters.

A low signal to noise ratio also makes the job of the receiver decoding the desired signal difficult.

A high SNR capability, in summary, is good for your LM3875 PCB for both good signal quality and device performance.

What Are The Ways Of Inspecting LM3875 PCB Assembly?

Professional and timely inspections must be conducted during the LM3875 Montagem PCB to note if there are defects that might lead to failure.

Failures could result from cracks, wettability, delamination, and component mounting.

Various inspection technologies can be employed in LM3875 PCB assembly depending on extent of defects coverage, cost, and performance.

The inspection technologies can be broadly categorized into structural process test inspections and visual inspections.

Inspeção visual

LM3875 PCBs assembly process has got several stages that can benefit from visual inspection. The assembling team can sample items for visual inspection based on the target and stage of inspection.

Visual inspection with naked eyes can help in spotting contaminating solder paste, missing components, and wrong placements.

Solder joints after reflow can be inspected by viewing reflected rays emanating from different directions.

Structural Test Inspection Systems

Visual inspections systems are suitable for easy to access, low cost, and small scale LM3875 PCB inspection needs. For large scale production where speed and accuracy are of essence, structural process test inspection systems are your best bet.

Structural inspection systems use digital means for real-time and automatic inspection and analysis.

They are therefore a significant improvement on what can be achieved by visual inspection.

Structural test inspection makes use of emissions such as x-rays, visible lights, and lasers.

The following structural inspection techniques may be used depending on the complexity of the LM3875 PCB to be inspected:

  • X-ray lamination system
  • Automated laser test (ALT)
  • X-ray fluoroscopic system
  • Inspeção óptica automatizada (AOI)

The appropriate inspection method for your LM3875 PCB will depend on the type of defect, the speed of inspection, and cost.

How Long Does LM3875 PCB Assembly Process Take?

LM3875 PCB assembly process takes 3-14 business days depending on the design requirements of the order.

That is exclusive of delays resulting from problems with the order or the Gerber file.

Boards typically take around 3 to 5 days to complete. The other time is spent on procuring components and materials (BOM processing) needed for the board.

It is advisable that you place your order way ahead before you need to use your LM3785 PCB. That will save you the delays that may result from problems with shipment or Gerber file.

What Factors Determine The LM3875 PCB Price?

Various factors go into consideration when determining the ultimate cost of an LMPCB. Some of these factors are:

Custos de mão de obra

The cost of labour is dependent on the region where the LM3875 PCB is assembled.

The assembly process is not 100% percent automated because human interaction is required in certain stages.

Cheap cost of labour implies that the total cost of the PCB will be cheaper and labour cost varies from region to region.

A board assembled in America, for instance, might be more expensive than that from Asia due to availability of cheap and skilled labour.

The reduced cost due to cheap labour may however be accompanied with other problems such as shipping costs and communication delays.

That increases turn time and may cause the cost to shoot again by about 20%.

Tempo de resposta

Turnaround time also influences the cost of LM3875 PCB. Shorter assembly time may increase the cost of your PCB up to 30% to 200% above the the normal assembly time cost.

An expedited order might mean that the manufacturer might have to put aside other tasks to focus on the urgent order.

The cost of urgent orders will definitely have to be higher to cover for the losses suffered due to holding other orders.

Likewise, expedited shipping will also result in higher costs of LM3875 PCBs.

The place of assembly may also be changed sometimes to expedite orders leading to significantly higher PCB prices.

Quantity Of LM3875 PCBs To Be Assembled

The unit price of LM3875 PCB assembly drops significantly if they are manufactured in large quantities as compared to only a few orders.

Factors such as programming, initial setup, and stencil add up to the cost for LM3785 PCB assembly.

Such factors have a significant bearing on the cost of the LM3875 PCB prototype.

They are, however, a onetime expenditure thus become insignificant when large quantities of PCBs are produced.

Tecnologia Usada

The technologies used in LM3875 PCB assembly are tecnologia de passagem (THT) or tecnologia de montagem em superfície (SMT), or both.

The technology selected also determines the price assembly cost of your PCB.

Surface mount technology is considerably cheaper due to low initial cost, high degree of automation, and high component density.

You can’t avoid to have through-hole components sometimes in your LM3875 PCB board and that implies through-hole technology must come into play.

Using through-hole technology raises the cost of the PCB because it needs additional drilling of the board and the routing area also reduces.

Packaging Of Parts

The cost of packaging the various parts of the LM3875 PCB also determines its cost of assembly.

Parts such as the BGA and QFNs have electrical connections below them and therefore require a lot of precision in packaging.

The parts (QFNs and BGAs) also need x-ray inspection to ensure there’s no short-circuiting and voids between the pins. These special packaging measures increase the cost of LM3785 PCB assembly.

How Do You Minimize The Effects Of Lead Inductance In LM3875 PCB?

Lead inductance can result in problems such as voltage surge in the LM3875 PCB.

To avoid that, it can be minimized by using a bigger bypass capacitor near the integrated circuit.

What Is The Best Way Of Grounding When Designing LM3875 PCB Layout?

The best way to effect the grounding is returning the low level, output compensation, and load grounds to the board’s common ground point.

The returning paths should be separate.

What Is The Maximum Input Voltage For LM3875 PCB?

The maximum input voltage for LM3875 PCB is 35V.

LM3875 PCB Kit

LM3875 PCB Kit

How Do Ensure Thermal Protection In LM3875 PCB Assembly?

An LM3875 PCB has an advanced thermal protection design meant to protect it from long-term thermal damages. The PCB shuts down when the die temperature hits 165 degrees Celsius.

The LM3875 PCB then then turns on when temperatures drop to about 155 degrees Celsius. The cycles of shut downs and turning on continue depending on temperature changes.

The LM3875 PCB can therefore heat up to a certain extent if the fault causing temperature changes doesn’t last for long.

A sustained fault will however make LM3875 cycle in a Schmitt Trigger manner within temperature limits of 155 and 165 degrees Celsius.

The Schmitt Trigger behaviour reduces the stress on the LM3875 PCB due to thermal cycles thus making it reliable under sustained fault situations.

The die temperature of the LM3875 PCB directly depends upon its heat sink.

The heat sink should therefore be selected with thermal considerations in mind so that the PCB does not suffer shutdowns during normal operations.

Choosing the right heat sink for your LM3875 PCB will lead to its long-term reliability.

What Are The Factors To Consider In The Design Of LM3875 PCBs?

Designing an outstanding LM3875 PCB starts with having a great layout.

The following are some factors to consider to ensure you have a robust board right from the beginning:

Diferentes Tipos de Vias

Através da can simply be looked at as what allows connections between the layers of LM3875 PCBs. The kind of vias you will need will depend on your needs because different boards have deferent thickness.

Your LM3875 PCB can be one-sided or multi-layered depending on what you need. You can choose from options such as buried, blind, micro, or through the hole.

Espessura do traço

Your LM3875 PCB’s thickness is measured in ounces of copper.

Most PCBs are either one or two ounces thick but manufactures can provide as many as six ounces depending on what you need.

The wrong trace thickness can cause you lamination and soldering problems so you should be keen to avoid that.

Gainclone with LM3875 PCB

Gainclone with LM3875 PCB


Creating guidelines on how to stack your PCB from the outset is useful in helping you figure the details of the board.

The number of levels will guide you in quantifying the materials needed and determining the time it takes to fabricate the PCB.

The Design Limitations

You must establish some rules to guide your PCB fabrication because that will ensure your needs are kept in mind.

You should focus on details such as time of flight analysis, components placement, layer allocation, and length of time for engineering.

Qualidade do sinal

Take into consideration the signal rise and fall times, the strength of the drive, the track lengths, and impedances.

Test those elements of your board before and after layout to determine if your needs are adhered to.

Which Are The Industry Certifications That LM3875 PCB Should Have?

Your LM3875 PCB should be able to perform under various physical handlings, temperatures, and other environmental conditions.

That can only be verified by conducting various tests.

There are various internationally recognized laboratories whose certifications are a guarantee your LM3875 PCB is designed to meet the required safety standards. Some of them are:

Certificações UL

Some of the common UL certifications include:

  • PCB standard UL 796: This certification focuses on the printed wiring boards (PWBs) guidelines for high-density interconnect, standard rigid, and metal based PCBs including LM3875 PCB.
  • PCB standard UL 796F : Covers flex and rigid-flex LM3875 PCBs
  • PCB standard UL 764E: Focuses on industrial laminates and materials used in making LM3875 PCBs
  • PCB standard 746F: Covers the dielectric film materials used in building LM3875 PCBs.
  • UL 94: Focuses on flammability standards for LM3875 PCBs

Tests carried out for UL certifications generally focus on:

  • Flame ratings – classified into V-0, V-1, V-2, VTM-0, VTM-1, and VTM-2
  • Solder limits – tests the soldering process used in the assembly of an LM3875 PCB. The test is meant to stimulate thermal shock and maximum temperature in order to gauge how the LM3875 PCB will perform
  • Temperatura operacional máxima
  • Direct support request
  • Índice de rastreamento comparativo
  1. Restriction of Hazardous Substances Directive RoHs certification
  2. Institute of Electrical and Electronics Engineers (IEEE) certification
  • International Organization for Standardization (ISO) certification

For all your LM3875 PCB, entre em contato agora.

Voltar ao Topo